View X24C45_135422.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

APPLICATION NOTES
AVAILABLE
AN3 * AN7 * AN8 * AN15 * AN16 * AN25 * AN29 * AN30 * AN35 * AN36 * AN39 * AN56 * AN69
X24C45 256 Bit
X24C45
Serial AUTOSTORETM NOVRAM
16 x 16 Bit
FEATURES
DESCRIPTION
The Xicor X24C45 is a serial 256 bit NOVRAM featuring a static RAM configured 16 x 16, overlaid bit-by-bit with a nonvolatile E2PROM array. The X24C45 is fabricated with Xicor's Advanced CMOS Floating Gate technology. The Xicor NOVRAM design allows data to be transferred between the two memory arrays by means of software commands or external hardware inputs. A store operation (RAM data to E2PROM) is completed in 5ms or less and a recall operation (E2PROM data to RAM) is completed in 2s or less. The X24C45 also includes the AUTOSTORE feature, a user selectable feature that automatically performs a store operation when VCC falls below a preset threshold. Xicor NOVRAMs are designed for unlimited write operations to RAM, either from the host or recalls from E2PROM and a minimum 1,000,000 store operations. Inherent data retention is specified to be greater than 100 years.
* * *
* * * * * *
AUTOSTORETM NOVRAM --Automatically Performs a Store Operation Upon Loss of VCC Single 5 Volt Supply Ideal for use with Single Chip Microcomputers --Minimum I/O Interface --Serial Port Compatible (COPSTM, 8051) --Easily Interfaced to Microcontroller Ports Software and Hardware Control of Nonvolatile Functions Auto Recall on Power-Up TTL and CMOS Compatible Low Power Dissipation --Active Current: 10mA --Standby Current: 50A 8-Lead PDIP and 8-Lead SOIC Packages High Reliability --Store Cycles: 1,000,000 --Data Retention: 100 Years
FUNCTIONAL DIAGRAM
NONVOLATILE 2 E PROM
ST O
STATIC RAM 256-BIT
EC AL
L
R
E
ROW DECODE
CONTROL LOGIC
R
RECALL (6) AS (7)
CE (1) DI (3) SK (2)
INSTRUCTION REGISTER
COLUMN DECODE
DO (4)
INSTRUCTION DECODE
4-BIT COUNTER
3833 FHD F01
AUTOSTORETM NOVRAM is a trademark of Xicor, Inc. COPS is a trademark of National Semiconductor Corp.
(c) Xicor, Inc. 1991, 1995, 1996 Patents Pending 3833-1.5 6/10/96 T3/C3/D0 NS
1
Characteristics subject to change without notice
X24C45
PIN DESCRIPTIONS Chip Enable (CE) The Chip Enable input must be HIGH to enable all read/ write operations. CE must remain HIGH following a Read or Write command until the data transfer is complete. CE LOW places the X24C45 in the low power standby mode and resets the instruction register. Therefore, CE must be brought LOW after the completion of an operation in order to reset the instruction register in preparation for the next command. Serial Clock (SK) The Serial Clock input is used to clock all data into and out of the device. Data In (DI) Data In is the serial data input. Data Out (DO) Data Out is the serial data output. It is in the high impedance state except during data output cycles in response to a READ instruction. AUTOSTORE Output (AS) AS is an open drain output which, when asserted indicates VCC has fallen below the AUTOSTORE threshold (VASTH). AS may be wire-ORed with multiple open drain outputs and used as an interrupt input to a microcontroller or as an input to a low power reset circuit. RECALL RECALL LOW will initiate an internal transfer of data from E2PROM to the RAM array. PIN NAMES Symbol CE SK DI DO RECALL AS VCC VSS Description Chip Enable Serial Clock Serial Data In Serial Data Out Recall Input AUTOSTORE Output +5V Ground
3833 PGM T01
PIN CONFIGURATION
DIP/SOIC
CE SK DI DO
1 2 3 4 X24C45
8 7 6 5
VCC AS RECALL VSS
3833 FHD F02.1
2
X24C45
DEVICE OPERATION The X24C45 contains an 8-bit instruction register. It is accessed via the DI input, with data being clocked in on the rising edge of SK. CE must be HIGH during the entire data transfer operation. Table 1. contains a list of the instructions and their operation codes. The most significant bit (MSB) of all instructions is a logic one (HIGH), bits 6 through 3 are either RAM address bits (A) or don't cares (X) and bits 2 through 0 are the operation codes. The X24C45 requires the instruction to be shifted in with the MSB first. After CE is HIGH, the X24C45 will not begin to interpret the data stream until a logic "1" has been shifted in on DI. Therefore, CE may be brought HIGH with SK running and DI LOW. DI must then go HIGH to indicate the start condition of an instruction before the X24C45 will begin any action. In addition, the SK clock is totally static. The user can completely stop the clock and data shifting will be stopped. Restarting the clock will resume shifting of data. RCL and RECALL Either a software RCL instruction or a LOW on the RECALL input will initiate a transfer of E2PROM data into RAM. This software or hardware recall operation sets an internal "previous recall" latch. This latch is reset upon power-up and must be intentionally set by the user TABLE 1. INSTRUCTION SET Instruction WRDS (Figure 3) STO (Figure 3) ENAS WRITE (Figure 2) WREN (Figure 3) RCL (Figure 3) READ (Figure 1)
X = Don't Care A = Address
to enable any write or store operations. Although a recall operation is performed upon power-up, the previous recall latch is not set by this operation. WRDS and WREN Internally the X24C45 contains a "write enable" latch. This latch must be set for either writes to the RAM or store operations to the E2PROM. The WREN instruction sets the latch and the WRDS instruction resets the latch, disabling both RAM writes and E2PROM stores, effectively protecting the nonvolatile data from corruption. The write enable latch is automatically reset on power-up. STO The software STO instruction will initiate a transfer of data from RAM to E2PROM. In order to safeguard against unwanted store operations, the following conditions must be true: * STO instruction issued. * The internal "write enable" latch must be set (WREN instruction issued). * The "previous recall" latch must be set (either a software or hardware recall operation). Once the store cycle is initiated, all other device functions are inhibited. Upon completion of the store cycle, the write enable latch is reset. Refer to Figure 4 for a state diagram description of enabling/disabling conditions for store operations.
Format, I2 I1 I0 1XXXX000 1XXXX001 1XXXX010 1AAAA011 1XXXX100 1XXXX101 1AAAA11X
Operation Reset Write Enable Latch (Disables Writes and Stores) Store RAM Data in E2PROM Enable AUTOSTORE Feature Write Data into RAM Address AAAA Set Write Enable Latch (Enables Writes and Stores) Recall E2PROM Data into RAM Read Data from RAM Address AAAA
3833 PGM T11
3
X24C45
WRITE The WRITE instruction contains the 4-bit address of the word to be written. The write instruction is immediately followed by the 16-bit word to be written. CE must remain HIGH during the entire operation. CE must go LOW before the next rising edge of SK. If CE is brought LOW prematurely (after the instruction but before 16 bits of data are transferred), the instruction register will be reset and the data that was shifted-in will be written to RAM. If CE is kept HIGH for more than 24 SK clock cycles (8-bit instruction plus 16-bit data), the data already shifted-in will be overwritten. READ The READ instruction contains the 4-bit address of the word to be accessed. Unlike the other six instructions, I0 of the instruction word is a "don't care". This provides two advantages. In a design that ties both DI and DO together, the absence of an eighth bit in the instruction allows the host time to convert an I/O line from an output to an input. Secondly, it allows for valid data output during the ninth SK clock cycle. D0, the first bit output during a read operation, is truncated. That is, it is internally clocked by the falling edge of the eighth SK clock; whereas, all succeeding bits are clocked by the rising edge of SK (refer to Read Cycle Diagram). LOW POWER MODE When CE is LOW, non-critical internal devices are powered-down, placing the device in the standby power mode, thereby minimizing power consumption. AUTOSTORE Feature The AUTOSTORE instruction (ENAS) sets the "AUTOSTORE enable" latch, allowing the X24C45 to automatically perform a store operation when VCC falls below the AUTOSTORE threshold (VASTH). WRITE PROTECTION The X24C45 provides two software write protection mechanisms to prevent inadvertent stores of unknown data. Power-Up Condition Upon power-up the "write enable" and "AUTOSTORE enable" latches are in the reset state, disabling any store operation. Unknown Data Store The "previous recall" latch must be set after power-up. It may be set only by performing a software or hardware recall operation, which assures that data in all RAM locations is valid. SYSTEM CONSIDERATIONS Power-Up Recall The X24C45 performs a power-up recall that transfers the E2PROM contents to the RAM array. Although the data may be read from the RAM array, this recall does not set the "previous recall" latch. During this power-up recall operation, all commands are ignored. Therefore, the host should delay any operations with the X24C45 a minimum of tPUR after VCC is stable.
4
X24C45
Figure 1. RAM Read
CE
SK
1
2
3
4
5
6
7
8
9
10
11
12
22
23
24
DI
1
A
A
A
A
1
1
X*
HIGH Z DO *Bit 8 of Read Instructions is Don't Care
3833 FHD F09.1
D0
D1
D2
D3
D13
D14
D15
D0
Figure 2. RAM Write
CE
SK
1
2
3
4
5
6
7
8
9
10
11
21
22
23
24
DI
1
A
A
A
A
0
1
1
D0
D1
D2
D12
D13
D14
D15
3833 FHD F10.1
Figure 3. Non-Data Operations
CE
SK
1
2
3
4
5
6
7
8
DI
1
X
X
X
X
I2
I1
I0
3833 FHD F11.1
5
X24C45
Figure 4. X24C45 State Diagram
POWER ON
POWER OFF RAM READ ENABLED
POWER-UP RECALL RAM READ
AUTOSTORE POWER DOWN STO OR WRDS CMD RAM READ ENABLED STO OR WRDS CMD RAM READ & WRITE ENABLED ENAS COMMAND STORE ENABLED AUTOSTORE ENABLED
RCL COMMAND OR RECALL RAM READ
WREN COMMAND
RAM READ OR WRITE
RAM READ & WRITE ENABLED STORE ENABLED
RAM READ OR WRITE
WREN COMMAND
3833 FHD F12.1
6
X24C45
ABSOLUTE MAXIMUM RATINGS* Temperature under Bias .................. -65C to +135C Storage Temperature ....................... -65C to +150C Voltage on any Pin with Respect to VSS ....................................... -1V to +7V D.C. Output Current ............................................. 5mA Lead Temperature (Soldering, 10 seconds) .............................. 300C RECOMMENDED OPERATING CONDITIONS Temperature Commercial Industrial Military Min. 0C -40C -55C Max. +70C +85C +125C
3833 PGM T02.1
*COMMENT Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and the functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Supply Voltage X24C45
Limits 5V 10%
3833 PGM T03.1
D.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise specified.) Limits Symbol lCC1 ICC2 ISB1 ISB2 ILI ILO VlL(1) VIH(1) VOL VOH VOL(AS) Parameter VCC Supply Current (TTL Inputs) VCC Supply Current (During AUTOSTORE) VCC Standby Current (TTL Inputs) VCC Standby Current (CMOS Inputs) Input Load Current Output Leakage Current Input LOW Voltage Input HIGH Voltage Output LOW Voltage Output HIGH Voltage Output LOW Voltage (AS) Min. Max. 10 2 1 50 10 10 0.8 VCC + 1 0.4 0.4 Units mA mA mA A A A V V V V V Test Conditions SK = 0.4V/2.4V Levels @ 1MHz, DO = Open, All Other Inputs = VIH All Inputs = VIH, CE = VIL DO = Open, VCC = 4.3V DO = Open, CE = VIL, All Other Inputs = VIH DO = Open, CE = VSS All Other Inputs = VCC - 0.3V VIN = VSS to VCC VOUT = VSS to VCC
-1 2 2.4
IOL = 4.2mA IOH = -2mA IOL (AS) = 1mA
3833 PGM T04.3
ENDURANCE AND DATA RETENTION Parameter Endurance Store Cycles Data Retention CAPACITANCE TA = +25C, f = 1MHz, VCC = 5V Symbol COUT(2) CIN(2) Parameter Output Capacitance Input Capacitance Max. 8 6 Units pF pF Test Conditions VOUT = 0V VIN = 0V
3833 PGM T06.1
Min. 100,000 1,000,000 100
Units Data Changes Per Bit Store Cycles Years
3833 PGM T05
Notes: (1) VIL min. and VIH max. are for reference only and are not tested. (2) This parameter is periodically sampled and not 100% tested.
7
X24C45
EQUIVALENT A.C. LOAD CIRCUIT
5V 919
A.C. CONDITIONS OF TEST Input Pulse Levels Input Rise and Fall Times Input and Output Timing Levels
100pF
0V to 3V 10ns 1.5V
3833 PGM T07.1
OUTPUT 497
3833 FHD F03
A.C. CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.) Read and Write Cycle Limits Symbol FSK(3) tSKH tSKL tDS tDH tPD1 tPD tZ tCES tCEH tCDS POWER-UP TIMING Symbol tPUR(4) tPUW(4) Parameter Power-up to Read Operation Power-up to Write or Store Operation Max. 200 5 Units s ms
3833 PGM T09
Parameter SK Frequency SK Positive Pulse Width SK Negative Pulse Width Data Setup Time Data Hold Time SK to Data Bit 0 Valid SK to Data Valid Chip Enable to Output High Z Chip Enable Setup Chip Enable Hold Chip Deselect
Min. 400 400 400 80
Max. 1
Units MHz ns ns ns ns ns ns s ns ns ns
3833 PGM T08.1
375 375 1 800 350 800
Notes: (3) SK rise and fall times must be less than 50ns. (4) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. These parameters are periodically sampled and not 100% tested.
8
X24C45
Write Cycle
1/FSK tSKH SK X 1 tSKL 2 n tCEH tCDS
SK CYCLE #
tCES CE tDS DI tDH
3833 FHD F04
Read Cycle
SK CYCLE # 6 SK 7 8 9 10 n
VIH CE tPD
DI
12
I1
DON'T CARE tPD1 tZ D0 D1 Dn HIGH Z
DO
HIGH Z
3833 FHD F05
9
X24C45
NONVOLATILE OPERATIONS Software Instruction NOP(5) RCL STO Write Enable Latch State X X SET Previous Recall Latch State X X SET
3833 PGM T10
Operation Hardware Recall Software Recall Software Store ARRAY RECALL LIMITS Symbol tRCC tRCP tRCZ Recall Timing
RECALL 0 1 1
Parameter Recall Cycle Time Recall Pulse Width(6) Recall to Output in High Z
Min. 2 500
Max.
Units s ns ns
3833 PGM T11
500
tRCC tRCP RECALL tRCZ DO HIGH Z
3833 FHD F06
SOFTWARE STORE CYCLE LIMITS Symbol tST Parameter Store Time After Clock 8 of STO Command Min. Typ.(7) 2 Max. 5 Units ms
3833 PGM T12.1
Notes: (5) NOP designates when the X24C45 is not currently executing an instruction. (6) Recall rise time must be <10s. (7) Typical values are for TA = 25C and nominal supply voltage.
10
X24C45
AUTOSTORE Cycle Limits Symbol tASTO VASTH VASEND Parameter AUTOSTORE Cycle Time AUTOSTORE Threshold Voltage AUTOSTORE Cycle End Voltage Min. 4.0 3.5 Max. 5 4.3 Units ms V V
3833 PGM T13.1
AUTOSTORE Cycle Timing Diagrams
5
VCC AUTOSTORE CYCLE IN PROGRESS VASTH VASEND
VOLTS (V)
4 3 2 1
tASTO STORE TIME TIME (ms)
VCC VASTH 0V tPUR tASTO tPUR
AS
3833 FHD F08
SYMBOL TABLE
WAVEFORM INPUTS Must be steady May change from LOW to HIGH May change from HIGH to LOW Don't Care: Changes Allowed N/A OUTPUTS Will be steady Will change from LOW to HIGH Will change from HIGH to LOW Changing: State Not Known Center Line is High Impedance
11
X24C45
PACKAGING INFORMATION
8-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P
0.430 (10.92) 0.360 (9.14)
0.092 (2.34) DIA. NOM.
0.255 (6.47) 0.245 (6.22)
PIN 1 INDEX PIN 1 0.300 (7.62) REF. 0.060 (1.52) 0.020 (0.51)
HALF SHOULDER WIDTH ON ALL END PINS OPTIONAL SEATING PLANE 0.150 (3.81) 0.125 (3.18)
0.140 (3.56) 0.130 (3.30)
0.020 (0.51) 0.015 (0.38) 0.062 (1.57) 0.058 (1.47) 0.020 (0.51) 0.016 (0.41)
0.110 (2.79) 0.090 (2.29)
0.015 (0.38) MAX.
0.325 (8.25) 0.300 (7.62)
TYP. 0.010 (0.25)
0 15
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
3926 FHD F01
12
X24C45
PACKAGING INFORMATION
8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S
0.150 (3.80) 0.158 (4.00) PIN 1 INDEX
0.228 (5.80) 0.244 (6.20)
PIN 1
0.014 (0.35) 0.019 (0.49) 0.188 (4.78) 0.197 (5.00)
(4X) 7
0.053 (1.35) 0.069 (1.75)
0.050 (1.27)
0.004 (0.19) 0.010 (0.25)
0.010 (0.25) X 45 0.020 (0.50)
0.050" TYPICAL
0 - 8 0.0075 (0.19) 0.010 (0.25) 0.016 (0.410) 0.037 (0.937) 0.250"
0.050" TYPICAL
FOOTPRINT
0.030" TYPICAL 8 PLACES
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
3926 FHD F22.1
13
X24C45
ORDERING INFORMATION
X24C45 Device
P
T
-V VCC Limits Blank = 5V 10% Temperature Range Blank = Commercial = 0C to +70C I = Industrial = -40C to +85C M = Military = -55C to +125C Package P = 8-Lead Plastic DIP S = 8-Lead SOIC
LIMITED WARRANTY
Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Xicor, Inc. makes no warranty of merchantability or fitness tor any purpose. Xicor, Inc. reserves the right to discontinue production and change specifications and prices at any time and without notice. Xicor, Inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xicor, Inc. product. No other circuits, patents, licenses are implied. US. PATENTS Xicor products are covered by one or more of the following U.S. Patents: 4,263,664; 4,274,012; 4,300,212; 4,314,265; 4,326,134; 4,393,481; 4,404,475; 4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846; 4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829,482; 4,874,967; 4,883,976. Foreign patents and additional patents pending. LIFE RELATED POLICY In situations where semiconductor component failure may endanger life, system designers using this product should design the system with appropriate error detection and correction, redundancy and back-up features to prevent such an occurrence. Xicor's products are not authorized for use as critical components in life support devices or systems. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its satety or effectiveness.
14

▲Up To Search▲

Price & Availability of X24C45

	To Download X24C45 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .